OTG kortlæser til Smartphones. 1 x SD og 1 x micro SD

USB 2.0, USB 1.1
Power from USB or AC / DC power adapter
read and write to PCMCIA hard disk, ATA Flash. DOES NOT READ SPECIAL CARDS!
read and write to CF-I, CF-II Smart Memory, Memory Stick, Micro Drive, Multimedia Card, Secure Digital Card and XD
Card use of additional Flash adapter.
Complete Plug and Play
USB Bootable from PCMCIA hard drive (depending on system BIOS support)
Serial ATA bootable from PCMCIA hard drive
Up to 480 Mbit/sec (60 MB/sec) data transfer* for USB 2.0, 10 times the speed of USB 1.1
Up to 1500 Mbit / second (150 MB / sec) data transfer to eSATA
USB version works under Windows 98SE, Me, 2000, XP, 7, 2003, Windows 10
Note! Certain cards are not supported Memory card and Verifone card. Buy the cards together with the reader to be sure!
Will not be returned because card cannot be read. Send any short, then we test whether the reader can read them.

Card Reader 8-In-One USB 3.0 Bus Powered.
2 x SD and 2 x Micro SD available
SDHC/Micro SDHC to SDHC/Micro SDHC
Compliant with the USB2.0 / 1.1 specification
Support CompactFlash Ultra DMA mode 6
Supports major memory cards including the SDXC
Plug & play simplicity
Auto detect card memory
support USB3.0 Ultra Hi speed transfer 100MB/s
Support 5Gbps Super SpeedU / 480Mbps high speed and full speed transfer rates
Supports bus powered modes

USB-B Mini 2.0 female (USB A to B cable medføger)
Supports: TF, CF, SD, Mini SD, SDHC, MMC, MS, XD
Power supply: 5VDC (via USB)
Cable length: 41 cm (Ex. connector)
Dimensions: 69.5 x 12.5 x 41 mm (W x D x H)

CompactFlash card interface for PC IDE bus
Suitable for PCs where the CF card is a disk drive

Mobil SD/ Micro SD kortlæser til Smartphones. Transportabel kortlæser OTG (On The Go) til Smartphones

Support 5V SATA III, SATA II and SATA I Drive and SSD
SATA II 3Gbps Controller Mini Vertical Adapter Card
44 Pin 2.0 mm IDE male connector for 5V DC and ATA signals
PCBA and SATA drives powered by Pin 41 & 42 of IDE connector 5V input
Compliant with Serial ATA 2.6
Jumper setting supports IDE Master, Slave and cable selection modes

Module that brings together a range of different functions in the front of the PC. USB-MULTI has built-in USB, FireWire, flash card reader, audio input/output and power supply (5V and 12V).

Cables are included that connect the various connectors to the existing connectors in the PC. For example, connect the USB cable to the USB connector that is already there. There is no USB or FireWire interface in the device, they must be in the PC already. Fits in all DANBIT 19” cabinets with a free 5¼” space.

Flash card reader/writer for the following cards: Compact Flash (Type I & II), Microdrive, SmartMedia (SM), MultiMedia Card (MMC), SecureDigital (SD) and Memory Stick (MS)

Audio: 1 x stereo outputs 2 x stereo inputs Mini jack

USB: 3 x USB 2.0 (Hi-Speed) 480 Mbit with A-type female connector

FireWire: 2 x FireWire 1394a 400 Mbit female connector

Voltage output: 1 x 12 VDC and 1 x 5 VDC, max. load 500 mA (can be used to power external devices)

Multi-funktionel enhed (flashkortlæser, batteribackup og wifi bridge), der kan konfigureres via browser eller app